Wet Sandblasting Equipment for Dust-Free Surface Preparation
Wet abrasive blasting equipment for fabricators, shipyards and engineering workshops that need to strip rust, paint and scale and prepare metal for recoating, without the dust of dry blasting.
- Low dust blasting
- No chemicals needed
- Uniform matte finish

Abrasive power with the control of water
Wet sandblasting mixes an abrasive into a high-pressure water jet to form an abrasive spray. When it strikes the surface it breaks away corrosion, old coatings and scale, leaving clean metal with a consistent profile ready for recoating. The water suppresses airborne dust, rinses away removed material and keeps the surface cool, so workpieces are cleaned without distortion or dimensional change.
Pumping Solutions supplies wet sandblasting equipment and pressure washer blasting kits for engineering, heavy fabrication, construction and marine work. Units can run sand of different grit sizes and alternative media such as baking soda or plastic pellets, so you can tune aggressiveness to the job, from heavy rust removal on steel structures to gentle deflashing of precision parts.
Key highlights
- Removes paint, rust, corrosion and scale
- Water suppresses dust from abrasive media
- No chemicals needed during operation
- Does not affect workpiece dimensions
- Produces a uniform matte anchor profile
- Works with sand, baking soda or plastic media
Advantages of wet abrasive blasting
Minimal dust
Water captures the fine particles that dry blasting releases into the air, improving visibility and reducing clean-up time and environmental concerns on site.
Uniform finish
Produces a homogeneous matte finish and a consistent anchor pattern across the surface, which helps new primers and coatings bond evenly and reliably.
Gentle on workpieces
Removes burrs and scale without damaging the part, and the light peening effect of the abrasive can help reinforce the surface of the workpiece.
Self-rinsing action
Removed coating and abrasive are flushed away continuously by the water jet, leaving a cleaner surface than dry blasting alone can achieve.
Flexible media
Choose sand grit size or softer media such as baking soda or plastic pellets to control how aggressive the blast is for each substrate.
Chemical-free process
No solvents or paint strippers are needed during blasting, reducing handling hazards, ventilation needs and chemical disposal costs in the workshop.
Wet sandblasting equipment specifications
| Pump flow rate | 14 to 30 LPM |
|---|---|
| Pump pressure | 140 to 500 bar |
| Pump motor | 5 HP |
| Wet blasting machine model | MA10102 |
| Cleaning rate | 1 to 2 metres per minute (depends on surface) |
| Air compressor requirement | 5 HP to 7 HP |
| Max. liquid pressure | 2500 psi (about 172 bar) |
| Abrasive tank capacity | 150 kg |
Wet sandblasting applications
Not sure this is the right fit?
Send us your duty point and site conditions. A pump engineer will check the selection and suggest alternatives if needed.
From enquiry to a running pump
A simple, engineer-led process — so you get the right pump the first time.
-
Share your duty
Tell us the liquid, flow, head, temperature and where the pump will run.
-
Get a sized proposal
Our engineers select the pump type, model, material and motor that fit the duty point.
-
Supply & installation
We supply the pump or system and can install, align and commission it on site.
-
Service that continues
Preventive maintenance, spares and repairs keep the system running efficiently.
Wet Sandblasting Equipment — FAQs
Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.
How is wet sandblasting different from dry sandblasting?
Dry blasting propels abrasive with compressed air and generates a lot of dust. Wet blasting adds water, which suppresses dust, cools the surface and rinses away debris. Wet blasting usually gives a more uniform matte finish and is gentler on the workpiece. The trade-off is that ferrous surfaces need a rust inhibitor afterwards and the water must be managed.
Do I need a rust inhibitor after wet blasting steel?
Yes. Freshly blasted steel is clean and reactive, and the water used in wet blasting can cause flash rust if the surface is left untreated. An anti-rust inhibitor is typically added to the water or applied immediately after blasting, and the surface should be coated promptly. We can advise on practical sequencing for your workshop.
What abrasive media can be used?
Sand of various grit sizes is common, with coarser grit giving a more aggressive cut. For delicate surfaces, softer media such as baking soda or plastic pellets can be used. The right choice depends on the substrate, the coating to be removed and the finish required before recoating.
Is the surface finish rougher than dry blasting?
Wet blasting can produce a slightly higher surface roughness than dry blasting with the same media, depending on settings. For many coating systems this profile helps adhesion. If a specific roughness is required, media type, grit size and pressure can be adjusted to bring the profile within the specification.
How is the water from wet blasting handled?
Water consumption is moderate but should be planned for. Spent water carries abrasive and removed coating, so it needs settling or filtration before disposal or recycling. On larger jobs, a simple settling tank arrangement helps recover water and keeps the work area tidy. Local disposal rules should always be followed.
What details do you need to recommend wet blasting equipment?
Tell us the material and size of the parts or structures, the coating or contamination to remove, the finish needed, expected daily area to clean, and whether you have compressed air and power on site. With this information we can recommend a pump, blasting kit or complete machine suited to your work.
Related high-pressure pumps
Choose the right wet sandblasting setup for your work
Share your material, coating and daily cleaning area, and we will recommend wet blasting equipment that fits.