Skip to content
+91 93630 47778contact@pumpscart.com Ambattur, Chennai · Supplying across India
Help centre

Pump questions, answered

Selection, materials, installation and maintenance — clear answers from our engineers. For product-specific questions, see the FAQs on each pump page.

  • Selection advice
  • Troubleshooting tips
  • Ordering help
FAQs

Choosing a pump

Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.

How do I calculate the head my pump needs?

Total head is the vertical height from the water source to the highest outlet (static head) plus friction losses in pipes, bends, valves and filters, plus any pressure needed at the outlet. As a rough guide, every 1 bar of required pressure equals about 10 m of head. Send us your pipe sizes, lengths and heights and we will calculate it for you.

What is the difference between flow and head?

Flow is how much liquid the pump moves per unit time (m³/h or LPM). Head is the height or pressure the pump can push that liquid against. Every centrifugal pump has a curve: as head rises, flow falls. The right pump meets your required flow at your required head, close to its best efficiency point.

When should I choose a multistage pump?

Choose a multistage pump when you need high pressure at moderate flow — high-rise water supply, boiler feed, RO feed, washing systems or long-distance transfer. Stacking impellers raises pressure without needing a very large single impeller or high speed.

Vertical or horizontal pump — which is better?

Vertical pumps save floor space and suit in-line installations and booster sets. Horizontal pumps are easier to access for maintenance and handle larger flows. The choice depends on space, flow, pressure and how you prefer to maintain the pump.

Why does pump efficiency matter so much?

A pump typically costs far more in electricity over its life than its purchase price. A pump running close to its best efficiency point uses less power, vibrates less and lasts longer. Oversized pumps throttled with valves waste energy every hour they run.

What is NPSH and why should I care?

NPSH (net positive suction head) is the pressure margin at the pump suction that prevents the liquid from vaporising. If the NPSH available at site is lower than the NPSH the pump requires, cavitation occurs — causing noise, vibration and impeller damage. We check this during selection.

FAQs

Materials & construction

Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.

Cast iron or stainless steel — what should I choose?

Cast iron is economical and suits clean water, HVAC and general duties. Stainless steel (SS304/SS316) resists corrosion and is preferred for treated water, RO, food, pharma, coolants and slightly aggressive liquids. Liquid chemistry and hygiene needs decide the material.

Mechanical seal or gland packing?

Mechanical seals give near-zero leakage and lower maintenance for most clean-liquid duties. Gland packing tolerates some solids and is simple to adjust, but allows controlled drip leakage. We recommend the seal type based on the liquid and duty.

Can your pumps handle hot water?

Yes — many centrifugal and multistage pumps are available for hot water duties. Temperature limits depend on the seal, elastomers and motor cooling, so always share the maximum liquid temperature when you enquire.

Which pump suits liquids with solids?

For liquids with suspended solids, choose pumps with open or semi-open impellers, larger passages or slurry designs. Standard multistage pumps are meant for clean liquids. Tell us the solids content and particle size so we can suggest the right design.

FAQs

Installation & operation

Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.

Why is my pump not delivering the rated pressure?

Common causes are air in the suction line, a clogged strainer, worn impellers or wear rings, wrong rotation direction, low supply voltage, or a system head different from what the pump was selected for. A site check with pressure readings usually pinpoints the cause.

How important is alignment for coupled pumps?

Very important. Misalignment between pump and motor shafts is a leading cause of bearing and seal failures and vibration. Coupled pump sets should be aligned during installation and rechecked after the piping is connected and after the first few weeks of operation.

Do I need a VFD for my pump?

A variable frequency drive saves energy when demand varies — such as pressure boosting in buildings, HVAC circulation and process loops. It also gives soft starting and constant pressure. For constant-duty applications, a correctly sized fixed-speed pump may be enough.

Can a pump run dry?

Most centrifugal pumps must not run dry — the mechanical seal can fail within seconds. Use dry-run protection, level controls or pressure switches, especially for borewell, tank-fed and booster systems.

FAQs

Service & maintenance

Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.

How often should industrial pumps be serviced?

It depends on duty and running hours. As a general guide: routine checks of leakage, noise and vibration weekly; bearing lubrication and alignment checks every few months; and a full inspection annually. Critical pumps benefit from a preventive maintenance contract.

What are the warning signs of pump failure?

Rising noise or vibration, seal leakage, higher power draw, drop in pressure or flow, overheating motor or bearings, and frequent tripping. Acting early avoids secondary damage to the shaft, impeller and motor.

Do you provide spare parts?

We help source spares such as mechanical seals, bearings, impellers and wear parts for the pumps we supply and for many common makes. Share the pump nameplate photo for a quick match.

Can you improve the efficiency of an existing system?

Yes. An energy audit compares actual operating points with pump curves. Typical fixes include impeller trimming, right-sizing, adding VFDs, correcting piping losses and replacing worn components.

FAQs

Ordering & support

Straight answers to the questions buyers ask us most. Can't find yours? Ask an engineer directly.

How do I request a quotation?

Use the quote form, call or WhatsApp us with the liquid, flow, head, temperature, suction condition and power supply. Photos of the existing pump and site help. We reply with a recommended model and itemised price.

Do you supply outside Chennai?

Yes. We supply pumps and pumping systems across India. Installation and service support outside Chennai are planned based on your location and project scope.

Can you match a pump to an existing tender specification?

Yes. Send the specification or BOQ and we will propose compliant models and highlight any points that need clarification.

Do you offer installation and commissioning with supply?

Yes. We can quote supply only, or supply with installation, commissioning and an ongoing service plan.

Still have a question?

Ask our engineers directly — we are happy to help even if you are just exploring options.